Handy Gay: Water line to Fridge!
Plumb the fridge
7 Oct To Tap Water Supply. 1. Turn off water at supply stop. 2. Install Saddle Valve, to the supply line (pipe in basement) to tap into water for the refrigerator. 3. Connect tubing to saddle valve. 4. Run tubing over a bucket and run water for 5 minutes. 5 . Run tubing to refrigerator - being careful not to kink or scar the. Imagine the convenience of having cold water or ice cubes any time you want them -- no more filling up pitchers to keep in the refrigerator or waiting for ice cube trays to freeze. But once you've bought a refrigerator with a cold water dispenser and automatic ice maker, you'll still need a way to get water into it. It takes. 11 Sep Here is a step-by-step water line installation refrigerator guide. A new refrigerator with a water dispenser and ice maker needs to be hooked up to a COLD water line. Usually behind where a refrigerator is installed, there will be a water valve that you can use to hook cold water to your fridge. If there is no.
Locate the nearest cold water line and shut it off. Once the tape is on the threads, connect the water line to the threaded section. Be sure to cut the end of the tubing square.
Running a water line to a refrigerator to supply its ice maker and drinking water dispenser has never been easier. MORE pretty much anywhere there is an existing shutoff valve. In most cases, the water line can be run from a kitchen faucet water supply line through the kitchen cabinets and over to the refrigerator.
If running the line through the cabinets is not feasible, you might need to run a line through the floor and up to where the refrigerator is located.
Flex water supply tubes are available in either a tough plastic nylon mesh or braided steel. Although the braided steel is considerably more expensive, the extra strength it provides is well worth the investment. It can be very inconvenient to move a refrigerator to get at a water line that has failed, so buy the best-quality water supply tube you can.
If so, your job is very easy. Turn the water supply valve on and check for leaks. MORE fittings as needed, using link pliers or an adjustable wrench. If you don't have a convenient water supply pipe and valve near the refrigerator, you must instead find another spot to hook up the water line.
Usually, this will be at some other existing water hookup, like the water supply lines connected to your sink faucet or dishwasher. An Adapt-a-Tee is an ideal plumbing fitting for this purpose. MORE Adapt-A-Tees are easy to install, and they provide the extra line you need with the least amount of work possible.
The type designed for copper pipe use simple compression fittings, and there are other types designed for attachment to CPVC or PEX water supply pipes. Adapt-a-Tees can be used in many situations where you need an extra line.
They come in various sizes to suit the job. You will also need a longer flex water supply tube to run from the water pipe to the refrigerator.
How to Hook Up a Water Line to a Refrigerator From the Sink | Home Guides | SF Gate
Measure the distance carefully, and buy a supply tube with plenty of length for the job. First, locate the shutoff valve under the kitchen sink where you want to connect the new water line. Link off the water at the valve that controls the cold-water supply pipe to the faucet.
If there are no branch shutoff valves, you can turn off the water by closing the main water supply valve to the entire house. Installing a Water Line Is a Snap. Continue to 2 of 7 below. Continue to 3 of 7 below. Continue to 4 of 7 below. Disconnect the Existing Water Line. Disconnect the faucet supply tube from the shutoff valve. Use two sets of pliers to safely remove the tube—one to hold the valve and one to unscrew it.
Be prepared for a small amount of MORE water leakage as you remove the valve—this is just the standing water in the water pipe, and it can easily be sponged up.
Continue to 5 of 7 below. Connect the Tee Adapter.
You can solve this with an ice maker installation kit that allows you to use the plumbing beneath the sink. We removed the drainpipes to clearly show this project. You'll want to use water lines that are already in place if possible, rather than attempting to install new pipes. How the Toto Washlet Works.
Attach the Adapt-a-Tee adapter to the shutoff valve, tightening by hand at first. Then finish tightening a little more with pliers; sure to use another set pliers to hold the shutoff valve and prevent it from twisting on the pipe while you tighten it.
Continue to 6 of 7 below. Use two pairs of channel-type pliers—one to grip the tee fitting, the other to tighten the supply tube onto the tee fitting. Continue to 7 of 7 below.
How to Connect a Refrigerator Water and Ice Dispenser - This Old House
Connect the Supply Tube to the Refrigerator. Run the new supply tube to the back of the refrigerator.
Tighten the connection just a little more than hand-tight, using pliers. Now turn on the faucet shutoff valve under the sink and check for leaks at the Adapt-a-Tee connections.
Also, check for leaks where the supply tube connects to the refrigerator before pushing the appliance back into place. If the refrigerator has a water dispenser, flush out several MORE gallons to purge the line of all the air.
If there is no water dispenser, throw away the first full batch or two of ice to make sure it is all clean and ready to use.
What can I do to prevent this in the future?